Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 57 | Manualshive

Page: 57 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

57

SET URV (246)
Entry

Set upper range value – without reference pressure.
Enter pressure value for the upper current value (20 mA).

Factory setting:

High sensor limit (





See PRESS. SENS HILIM, Page 119)

GET LRV (309)
Entry

Set lower range value – reference pressure is present at device.
The pressure for the lower current value (4 mA) is present at device. With the "Confirm"
option, you assign the lower current value to the pressure value present.
On-site display: the pressure value present is displayed in the bottom line.

Options:

• Abort
• Confirm

GET URV (310)
Entry

Set upper range value – reference pressure is present at device.
The pressure for the upper current value (20 mA) is present at device. With the "Confirm"
option, you assign the upper current value to the pressure value present.
On-site display: the pressure value present is displayed in the bottom line.

Options:

• Abort
• Confirm

DAMPING VALUE (247)
Entry

Enter damping time (time constant



).

The damping affects the speed at which all subsequent elements, such as the on-site
display, measured value and current output react to a change in the pressure.

Input range:

0.0...999.0 s

Factory setting:

2.0 s or as per order specifications

Table 7: (GROUP SELECTION



) OPERATING MENU



SETTINGS



BASIC SETUP "Pressure"

Parameter name

Description

«
...
55
56
57
58
59
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 54

Brand: IHP Pages: 8

Ergopower Record 12s

Brand: CAMPAGNOLO Pages: 124

Brand: CAMPAGNOLO Pages: 100

Brand: FeiYu Tech Pages: 6

Brand: Faudi Pages: 18

Brand: IFM Pages: 12

Brand: IFM Pages: 13

Efector 200 Series

Brand: IFM Pages: 4

Brand: IFM Pages: 33

Brand: oliser Pages: 6

Brand: Keis Pages: 2

Brand: Darimo Pages: 2

Brand: La Crosse Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands