Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 134 | Manualshive

Page: 134 / 156

background image

Trouble-shooting

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

134

Hauser

604 (W604)

Warning
C

Funktion
check (C)

C>Linearisation table not valid.
Less than 2 points or points too
close

!

Note!

From software version "02.10.xx" onwards, there is no min. span for the
Y-points.

– The linearisation table consists of

less than 2 points.

– Add to linearisation table. If

necessary, perform linearisation
again.

58

– At least 2 points in the

linearisation table are too close
together. A minimum gap of 0.5
% of the distance between two
points must be maintained.
Spans for the "Pressure
linearized" option: HYDR. PRESS
MAX. – HYDR. PRESS MIN.;
TANK CONTENT MAX. – TANK
CONTENT MIN.
Spans for the "Height linearized"
option: LEVEL MAX – LEVEL
MIN; TANK CONTENT MAX. –
TANK CONTENT MIN.

– Correct linearisation table and

accept again.

613 (W613)

Warning
I

Funktion
check (C)

I>Simulation is active

– Simulation is switched on, i.e.

the device is not measuring at
present.

– Switch off simulation.

60

620 (E620)

Error
C
Factory
setting:
Warning C

Out of
specification
(S)

C>Current output out of range

The current is outside the permitted
range 3.8 to 20.5 mA.

– The pressure applied is outside

the set measuring range (but
within the sensor range).

– Check pressure applied,

reconfigure measuring range if
necessary (



See also these

Operating Instructions, chapter 4
to 6.)

– Perform reset (Code 7864) and

carry out calibration again.

49

– Loose connection at sensor cable

– Wait a short period of time and

tighten the connection, or avoid
loose connection.

700 (W700)

Warning
C

Maintenance
request (M)

C>Last configuration not
stored

– An error occurred when writing

or reading configuration data or
the power supply was
disconnected.

– Perform reset (Code 7864) and

carry out calibration again.

54

– Main electronics defect.

– Replace main electronics.

701 (W701)

Warning
C

Funktion
check (C)

C>Measuring chain config.
exceeds sensor range

– The calibration carried out would

result in the sensor nominal
operating range being undershot
or overshot.

– Carry out calibration again.

50

702 (W702)

Warning
C

Maintenance
request (M)

C>HistoROM data not
consistent.

– Data were not written correctly

to the HistoROM, e.g. if the
HistoROM was detached during
the writing process.

– Repeat upload.
– Perform reset (Code 7864) and

carry out calibration again.

55

– HistoROM does not have any

data.

– Copy suitable data to the

HistoROM. (



See also

Operating Instructions
BA00270P (Deltabar S),
BA00271P (Cerabar S) or
BA00332P (Deltapilot S), Section
5.5.1 "Copying configuration
data".)

703 (A703)

Alarm
B

Failure (F)

B>Measurement error

– Fault in the main electronics.

– Briefly disconnect device from

the power supply.

22

– Main electronics defect.

– Replace main electronics.

Code

Error type/
NA 64

Corresponds
NE 107

Message/description

Cause

Measure

Prio
rity

«
...
132
133
134
135
136
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Super G3 FAX Board-T1

Brand: Canon Pages: 16

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Canon Pages: 6

7215 - LV XGA LCD Projector

Brand: Canon Pages: 8

Brand: GCE Pages: 16

Brand: GCC Technologies Pages: 12

Brand: Navibe Pages: 8

Brand: S&B Filters Pages: 7

Brand: Tait Pages: 10

Powersaver Dual Flexi

Brand: Sangamo Pages: 2

StudSensor HD25

Brand: Zircon Pages: 2

Brand: Öhlins Pages: 8

Brand: COOLFORT Pages: 16

Brand: Fuzion Pages: 8

USB temperature

Brand: MADRIX Pages: 2

Brand: DITEC Pages: 2

Brand: Hunter Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands