EMBRON Hatteland X Series, User Manual

Page: 97 / 134

97
IND100129-246
All specifications are subject to change without prior notice!
Specifications - HD 55T22 MVD-MAx-CORx
Console/External Remote Model - HW00 version
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hattelandtechnology.com for the latest electronic version.
2/2
• W:1346.83 [53.02''] x H:817.63 [32.19''] x D:99.00 [3.90"] mm [inch]
• Weight: Approx. 70.2 kg / 154.4lbs
• High Quality TFT with LED Backlight Technology
• 55.0 inch viewable image size, Widescreen, Aspect Ratio 16:9
• TFT active-matrix liquid crystal panel, RGB vertical stripe
• MVA (Multi-domain Vertical Alignment) LCD Technology
• Native Resolution : 3840 x 2160 (UHD, 4K)
• Pixel Pitch (RGB) : 0.315 (H) x 0.315 (V) mm
• Response Time : 6.5 ms (typical) (G to G)
• Contrast Ratio : 4000:1 (typical)
• Light Intensity : 450 cd/m ² (typical)
• Viewable Angle : +/- 89 deg. (typical) (Up/Down/Left/Right)
• Active Display Area : 1209.6 (H) x 680.4 (V) mm
• Max Colors : 16.7 million
A P P R O V A L S & C E R T I F I C A T E S
Physical Considerations:
TFT Technology:
TFT Characteristics:
These products have been tested / type approved by the following classification societies:
IEC 60945 4th (EN 60945:2002) IACS E10 EU RO MR
- Mutual Recognition
ClassNK
- Nippon Kaiji Kyokai
CCS - China Classification Society
External Remote Controller via HD REM SX1-A1:
• 3 physical buttons for user interaction, but conforms with the
standardized 6 button functionality; (Bri, Brightness-, Menu,
Navigation<, Navigation> and Power).
Communicates via Hatteland Technology SCOM RS-485 protocol
User Controls:
Multi-power Supply:
• 115&230VAC - 50/60Hz + 24 VDC
Note: You may connect either AC power or DC power or both. In case both sources
are connected, power will be sourced from the AC input. If AC input is lost, there will
be a uninterrupted switch-over to DC input.
Power Consumption:
• Operating: 145W (typ) - 220W (max)
Power Specifications:
Resolutions:
VGA (640 x 350) to UHD (3840 x 2160*)
- Review Timing Table in User Manual
*
Recommended for optimal picture quality
Supported Signals:
• Operating : Temperature -15 deg. C to +55 deg. C
• Storage : Temperature -30 deg. C to +70 deg. C
• Humidity : Up to 95% (Operating / Storage)
• IP Rating : Protection: IP66 front - IP22 rear (EN60529)
• Compass Safe Distance : Standard: 500cm - Steering: 230cm
Lifetime Considerations:
Even though the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
• Projected Capacitive Touch Screen (Multitouch, USB, Pen/Glove support)
Environmental Considerations:
Factory Options:
• Optical Bonding Technology
• External Remote Control, EN60945 Tested (HD REM SX1-A1)
Factory Default:
• Color Calibrated models (ECDIS)*
• Revised User Controls with ECDIS Compliance*
*Please review model HD 55T22 MVD-MAx-COTx datasheet.
Prepared for:
• HD REM SX1-A1 : 1 x External Remote Control, EN60945 Tested
Please see user manual/datasheet for more information
Available Accessories:
Signal Terminals:
• DVI-D Input ** : 1 x 24p DVI (female) - Max 3840x2160@30Hz
• VGA Input ** : 1 x 15p HD D-SUB (female) - Max 1920x1200@60Hz
• HDMI 2.0 Input ** : 1 x 19p HDMI (female) - Max 3840x2160@60Hz
• DP 1.2 Input ** : 1 x 20p DisplayPort (female) - Max 3840x2160@60Hz
• SCOM+Touch : 1 x USB TYPE A Connector (female)
• SCOM RS-422/485 : 1 x 5-pin Terminal Block 3.81 non-is Buzzer
Factory default reserved for HD REM SX1-A1 control
• SCOM Ethernet * : 1 x RJ45 Connector
• SCOM RS-232 * : 1 x 9p D-SUB (female) non-isolated
• User Interface *** : 1 x 9p D-SUB (male) - Potentiometer Analog Input,
User Brightness (BRT), I2C, +5VDC & 12VDC OUT,
Power ON/OFF
• SW Interface : 1 x USB TYPE A (female) for Firmware Update
• GDCx Interface : 1 x 15p D-SUB (male) for xDC Hardware Comm.
• AC Power IN : 1 x Std IEC Inlet
• DC Power IN : 1 x 2p D-SUB Connector (male) - Amphenol FCC17
Notes:
* SCOM via Ethernet/RS-232 is inhibited if HD REM SX1-A1 is in use(User Controls).
** Alternative solution for brightness adjustment is DDC/CI or use user interface for
brightness and on/off controls.
*** HD REM SX1-A1 can be removed and SCOM can be used.