EMBRON Hatteland X Series, User Manual

Page: 124 / 134

Pinout Assignments
124
IND100241-25
Appendix
20-pin DisplayPort (DP) Female
20 18 16 14 12 10 8 6 4 2
19 17 15 13 11 9 7 5 3 1
PIN 01 ML_Lane 0 (p) - Lane 0 (positive)
PIN 02 GND - Ground
PIN 03 ML_Lane 0 (n) - Lane 0 (negative)
PIN 04 ML_Lane 1 (p) - Lane 1 (positive)
PIN 05 GND - Ground
PIN 06 ML_Lane 1 (n) - Lane 1 (negative)
PIN 07 ML_Lane 2 (p) - Lane 2 (positive)
PIN 08 GND - Ground
PIN 09 ML_Lane 2 (n) - Lane 2 (negative)
PIN 10 ML_Lane 3 (p) - Lane 3 (positive)
PIN 11 GND - Ground
PIN 12 ML_Lane 3 (n) - Lane 3 (negative)
PIN 13* CONFIG1 - connected to Ground*
PIN 14* CONFIG2 - connected to Ground*
PIN 15 AUX CH (p) - Auxiliary Channel (positive)
PIN 16 GND - Ground
PIN 17 AUX CH (n) - Auxiliary Channel (negative)
PIN 18 Hot Plug - Hot Plug Detect
PIN 19 Return - Return for Power
PIN 20 DP_PWR - Power for connector (3.3 V 500 mA)
*Pins 13 and 14 may either be directly connected to ground or
connected to ground through a pulldown device. This is the pinout for
source-side connector, the sink-side connector pinout will have lanes
0–3 reversed in order; i.e., lane 3 will be on pin 1(n) and 3(p) while
lane 0 will be on pin 10(n) and 12(p).
19-pin HDMI Female
18 16 14 12 10 8 6 4 2
19 17 15 13 11 9 7 5 3 1
PIN 01 TMDS Data2+
PIN 02 TMDS Data2 Shield
PIN 03 TMDS Data2−
PIN 04 TMDS Data1+
PIN 05 TMDS Data1 Shield
PIN 06 TMDS Data1−
PIN 07 TMDS Data0+
PIN 08 TMDS Data0 Shield
PIN 09 TMDS Data0−
PIN 10 TMDS Clock+
PIN 11 TMDS Clock Shield
PIN 12 TMDS Clock−
PIN 13 CEC
PIN 14
Reserved (HDMI 1.0–1.3a)
Utility/HEAC+ (HDMI 1.4+, optional,
HDMI Ethernet Channel and Audio
Return Channel)
PIN 15 SCL (I²C Serial Clock for DDC)
PIN 16 SDA (I²C Serial Data for DDC)
PIN 17 Ground (for DDC, CEC, ARC and HEC)
PIN 18 +5 V (min. 0.055 A)
PIN 19
Hot Plug Detect (all versions)
HEAC- (HDMI 1.4+, optional, HDMI
Ethernet Channel and Audio Return
Channel
Serial COM RS-232 non-isolated, 9-pin DSUB Female
5 4 3 2 1
9 8 7 6
PIN 01** BUZ+ Buzzer Control Positive IN*
PIN 02 TxD Transmit Data
PIN 03 RxD Receive Data
PIN 04 DTR Data Terminal Ready
PIN 05 GND Ground
PIN 06 DSR Data Set Ready
PIN 07 RTS Request To Send
PIN 08 CTS Clear To Send
PIN 09** BUZ- Buzzer Control Negative IN*
RS232-Wake On Ring is not enabled. **See notes in blue.
Suggested “Buzzer” Control Logic inside Computer/System:
Pin 1 on your Connector
Pin 1 Pin 9
9-pin DSUB Male Add
Note Orientation! Back Shell
Logic Control
GND
+12V
NPN
Transistor
Rating:
500mA
Internal Side External Side
Note: Requires soldering and assembly. It is expected that the
technician has experience in electronics, soldering and assembling cables and
connectors. Use a cable that contains at least 2 wires (not 2 single wires). Heat
Shrink Tubes must be applied to soldered wire/pins. Test connection (beep)
with Voltage Meter. Wires may be combined if using RS-232 COM as well.