Physical Connections
44
IND100133-58
POWER INPUT AC:
The internal AC power module supports both 115VAC/60Hz and 230VAC/50Hz power input. Please check
specifications for your unit.
+ -
POWER INPUT DC:
Connect your DC power cable to the 2P Amphenol FCC17 D-SUB Connector (male). Secure the cable to the hex
spacers provided on the unit, and secure the other end to your power supply. The internal DC power module supports
24VDC.
Multi-power note:
(For units supporting AC & DC input simultaneously)
The unit has a dual input power supply which will accept both AC and DC input. If both inputs are connected, the
unit will be powered by AC. If AC is disconnected it will automatically switch over to DC without affecting the operation
of the unit. This makes it possible to use AC power as primary power and a 24V battery as secondary power,
eliminating the need for expensive UPS systems.
DC Power for Chart & Planning Table / Floor Tilt models:
:
Even tough the Chart & Planning Table / Floor Tilt model is by factory default configured with AC power input only, users can also
connect DC power to these models internally. Normally the AC power will power the lift, tilt mechanism, internal computer (example
HT C02) and provide power to the actual display unit in total. By factory default, the DC connector is not used.
All 55 inch models feature Multi-power and the DC connector are always fully functional. In some cases, users might turn off or
loose AC momentarily onboard which would also turn the display unit off and loose signal. If users still want the display unit in Chart
Table to be powered, simply connect suitable DC power to let it function as redundant, backup power to the Display unit. Depending
on what computer are installed/connected to the Chart & Planning Table / Floor Tilt Model, consider also adding DC power to that to
ensure software/systems can still function and provide image to the 55 inch unit. However, note that the DC power connected to the
display unit, will NOT give power to the lift, tilt mechanism and connected computer. Lift and Tilt mechanism require AC power.
To get access to the DC power input for the Chart & Planning Table / Floor Tilt model, please refer to “Installation Procedures/
Access to Display Connectors (Table Model)” section earlier in this manual.
RS-422 / RS-485 COM I/O:
The COM (non-isolated RS-422/485) allows functionality to communicate with serial based equipment including
external buzzer functionality. Connect and fasten your cables from your compatible external equipment to the 5-pin
Terminal Block 3.81 connector. Please review the “Pinout Assignments” chapter as well as “Housing / Terminal Block
Connector Overview” in this manual for more information. One example of perheripal from Hatteland Technology is the
External Remote Controller (HD REM SX1-A1). This connector will allow remote control of the display unit to control
common functions like brightness, input source and more via the Serial Remote Control (SCOM) as provided by
Hatteland Technology.
Hatteland Technology’s Serial Remote Control Interface (SCOM) protocol document can be downloaded from:
https://www.hattelandtechnology.com/hubfs/pdfget/inb100018-6.htm
Summary of Contents for Hatteland X Series
