Elkron MP 110 Manual Download Page 24

Page: 24 / 68

(((ELKRON))) - MP110

FACTORY

PROGRAMMABILITY

Transponder

Disabled

3 to 15 rings

Telephone selection

DTMF

DTMF/Impulsive

Tone control

Disabled

Disabled/enabled

Answer control

Disabled

Disabled/enabled

Routing

Disabled

Disabled/enabled

Protocol

IDP

IDP/ADF/S1400/C200b/141910/141820/231820/231840/SIA/DGF

Answering system skip

Enabled

Enabled/disabled

Communicator enabling

OR sectors

AND/OR sectors

INPUTS FUNCTIONS

ZA1

ZA2

ZA3

ZA4

ZA5

ZA6

ZA7

ZA8

Instant Burglary

Delayed Burglary

Chime Burglary

Final Exit Burglary

Silent Panic

Panic with sirens

Technological

Fire

Associated to sector 1

Associated to sector 2

Associated to sector 3

KEYBOARD INPUTS

ZB1

ZB2

ZB3

ZB4

ZB5

ZB6

ZB7

ZB8

Instant Burglary

Delayed Burglary

Chime Burglary

Final Exit Burglary

Silent Panic

Panic with sirens

Technological

Fire

Associated to sector 1

Associated to sector 2

Associated to sector 3

3.1.4 Factory parameters: reader inputs

3.1.5 Factory parameters: 1/4 keyboards inputs

HOW TO READ TABLE

The symbol

indicates the

zone as programmed in fac-
tory.

The symbol indicates that
the zone may be pro-
grammed.

The white space indicates
that the zone may not be
programmed.

HOW TO READ TABLE

The symbol

indicates the

zone as programmed in fac-
tory.

The symbol indicates that
the zone may be pro-
grammed.

The white space indicates
that the zone may not be
programmed.

3.1.6 Communicator factory parameters

Summary of Contents for MP 110





































































Search results

Summary of Contents for MP 110

Reviews:

Related manuals for MP 110

Brands by name

Popular brands

Elkron MP 110, Manual

Search results

Summary of Contents for MP 110

Reviews:

Related manuals for MP 110

Brands by name

Popular brands