Elkron MP 110 Manual Download Page 51 | Manualshive

Page: 51 / 68

background image

(((ELKRON))) - MP110

The

led shows the relay ena-

bling to the tamper management with
control unit in OFF.
Led on = enabled alarm

The

led shows the relay

enabling to the fire alarm manage-
ment.
Led on = enabled alarm

The

led shows the level pro-

gramming.
Led on= energized relay under quies-
cent conditions
Led off= de-energized relay under
quiescent conditions

The

led shows the level pro-

gramming
Led on = NH level
Led off = NL level
By programming the NH level the
output provides a positive under qui-
escent conditions
By programming the NL level the out-
put provides a positive under alarm
conditions

1. Enter the Engineer’s code and press key

EXIT

F

+ key

4

twice: the

output 1 programming (control unit relay) is visualized (leds

,

et

turn on).

Output 1 Programming (CONTROL UNIT relay)

2.

NH/NL level programming ( energized or de-energized relay)

Press key

4

. Press key

A

to program the desired level on the

relay.

3.

TAMPER IN OFF

Press key

S

to enable/disable the control unit relay for TAMPER

IN OFF.

4.

FIRE ALARM MANAGEMENT

Press key

O

to enable/disable the output to the FIRE alarm

management.

Programming of other outputs

Follow the procedures described in item 1.

5.

Through keys

1

2

, select the output to be programmed.

The outputs relevant to the peripherals are proposed only if these are
present. The LED keypads show the output number in a flashing mode.

6.

When the output to be programmed is visualized, press key

4

.

7.

Press key

A

to program the NH/NL level of the output under

reference.

8.

Press keys

1

2

to select the type of alarm that the output

shall carry out. The LED keypads will show the alarm mode in a fixed
mode with a value from 0 to f according to the following table:

00 = burglary

08 = TC

01 = tamper

09 = reset

02 = panic

0A = buzzer

03 = technical

0B = system status

04 = fire

0C = open zone

05 = CHIME

0D = telephone line

06 = Failure
07 = LPA

9. If the chosen type is Burglary or TC, use key

E

to program the

AND/OR sectors mode. Moreover the sectors associated with the
output under reference are visualized by the corresponding leds

1 3

,

2

,

3

that turn on. It is possible to associate

The

led shows the AND/OR

mode of the sectors associated to an
output of burglary type ( sector alarm)
or TC type.

BURGLARY OUTPUT PRO-
GRAMMED IN OR
The output commutates if an alarm is
generated in one of the associated
sectors.

BURGLARY OUTPUT PRO-
GRAMMED IN AND
The output commutates if the associ-
ated sectors are all armed and an
alarm is generated in one of these
sectors.

SECTOR TC IN OR
The lock positive is missing if all
associated sectors are armed.

SECTOR TC IN AND
The lock positive is missing if at least
one of the associated sectors is armed.

51

«
...
49
50
51
52
53
...
»

Summary of Contents for MP 110





































































Reviews:

No comments

Related manuals for MP 110

Brand: OmarLift Pages: 14

Brand: C.Nord Pages: 100

CoreBuilder 9000

Brand: 3Com Pages: 78

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: Datalogic Pages: 15

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: Lawler Pages: 5

Brand: Universal Remote Pages: 20

Brand: Polycom Pages: 2

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Roger Pages: 21

Brand: Pfeiffer Vacuum Pages: 100

Brand: Atmel Pages: 12

TrueAlarm 4100 Series

Brand: Simplex Pages: 8

Brand: LAUNDRY SOLUTION Pages: 14

TITAN CONTROLS KRONUS 2

Brand: Sunlight Supply Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands