Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download Page 118 | Manualshive

Page: 118 / 172

background image

110

New trail, named Trail 3, is created when Trail 2 is made inactive. Any

new travel will be recorded in this trail, which is active and visible.

Trails do not need to be visible in order to be active.

You can save and recall up to 10 different plot trails.

Tip:

Another quick way to stop recording one trail and begin a new one
is to use the New Trail command. Press

MENU

|

MENU

|

↓

to

M

Y

T

RAILS

|

ENT

. Use

→

to select

N

EW

T

RAIL

and press

ENT

.

Caution:

You also have the option of completely turning off trail record-
ing, under the trail Options command. If, however, the Update
Active Trail option is left turned off, it will cancel the automatic
trail creation feature.

Displaying a Saved Trail

The active trail is automatically displayed on the with the default set-
tings. You can selectively turn trail display on and off for any saved or
active trail. In the Saved Trails List, visible trails have a check mark in
front of the trail name.

«
...
116
117
118
119
120
...
»

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

troller 2.0 combo

Brand: Marcum Technologies Pages: 13

Brand: Standard Horizon Pages: 144

Brand: Raytheon Pages: 224

Fish Seeker US600

Brand: PNI Pages: 88

Brand: Friday Lab Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands