Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download Page 85 | Manualshive

Page: 85 / 172

background image

77

The bottom depth and surface temperature (if the unit is equipped with
a temperature sensor or a transducer with a temp sensor built in) show
at the top left corner of the screen.

The FasTrack™ display shows just to the right of the scale. This
changes all echoes into short horizontal bars, replicating a flasher so-
nar. The zoom bar on the far right shows the area that is zoomed when
the zoom is in use. (See the Zoom section for more information.)

Full Sonar Chart. The Overlay Data (depth and water temperature)

are set to a different text size.

Split Zoom Sonar Chart

A split chart shows the underwater world from the surface to the bot-
tom on the right side of the screen. The left side shows an enlarged ver-
sion of the right side. The zoom range shows at the bottom left corner of
the screen.

«
...
83
84
85
86
87
...
»

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

Brand: Samyung Pages: 33

Brand: Humminbird Pages: 92

Brand: Standard Horizon Pages: 42

Brand: Matrix Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands