Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download

Page: 28 / 172

Insert bolt and check transducer position on transom.

3. Assembling the transducer.

Once you determine the correct posi-

tion for the ratchets, assemble the transducer as shown in the fol-
lowing figure. Don't tighten the lock nut at this time.

Assemble transducer and bracket.

4. Drilling mounting holes.

Hold the transducer and bracket assembly

against the transom. The transducer should be roughly parallel to the
ground. The transducer's centerline should be in line with the bottom
of the hull. Don't let the bracket extend below the hull!

Ratchets

Nut

Metal
washer

Metal washer

Bolt

Rubber
washers

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands