Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download

Page: 158 / 172

150

To adjust the display's brightness:

From the screen menu, press

↓

RIGHTNESS

. Press

←

→

to move the

bar. The left end of the scale is minimum contrast. The right end is
maximum contrast.

To adjust the screen's display mode:

From the screen menu, press

↓

ISPLAY

ODE

ENT

|press

↑

↓

to se-

lect

mode

EXIT

Display Mode menu.

Set Language

This unit's menus are available in 10 languages: English, French, Ger-
man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish.
To select a different language:

1. Press

MENU

↓

YSTEM

ETUP

ENT

2. Press

↓

ANGUAGE

ENT

3. Use

↓

↑

to select the desired language and press

ENT

. All menus now

appear in the language you selected.

Set Local Time

Using the local time setting is handy when estimating arrival time. The
time and date are saved when a waypoint is created.

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands