Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download Page 75 | Manualshive

Page: 75 / 172

background image

67

To turn the Fish I.D. feature on:

1. From the Sonar Page, press

MENU

|

↓

to

S

ONAR

F

EATURES

|

ENT

.

2. Press

↓

to

F

ISH

ID S

YMBOLS

|

ENT

|

EXIT

|

EXIT

.

To turn off Fish I.D., repeat these instructions.

FishTrack



The FishTrack feature shows the depth of a fish symbol when it ap-
pears on the display. This lets you accurately gauge the depth of tar-
gets. This feature is available only when the Fish I.D. feature is on. The
default setting for FishTrack is off.

To turn on FishTrack:
NOTE:

These instructions will turn on FishTrack

and

Fish I.D. at the same

time.

1. From the Sonar Page, press

MENU

|

↓

to

S

ONAR

F

EATURES

|

ENT

.

2. Press

↓

to

F

ISH

ID D

EPTHS

|

ENT

|

EXIT

|

EXIT

.

To turn off FishTrack, repeat these instructions. Turning off FishTrack
in this manner will not turn off Fish I.D. symbols.

Sonar Features menu with Fish I.D. Depths selected (left). Sonar Page

showing Fish I.D. symbols and FishTrack depths turned on (right).

Symbols with

FishTrack depths

«
...
73
74
75
76
77
...
»

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

Brand: Garmin Pages: 50

StructureMap HDS Gen 2

Brand: Lowrance Pages: 8

Fishfinder 160C

Brand: Garmin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands