Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download Page 55

Page: 55 / 172

Sonar Page Menu.

Sonar Menu Commands

Sensitivity

: sets threshold of sonar echoes shown on sonar chart.

Auto Sensitivity

: automatically adjusts sensitivity based on depth.

GrayLine



: separates fish and structure near the bottom from the

actual bottom and defines bottom composition/hardness.

Depth Range

: manually sets the depth range shown on sonar chart.

Auto Depth Range

: automatically sets the depth range shown on the

sonar chart to always keep the bottom in view.

Stop Chart

: stops the sonar chart from scrolling. Used when you want

to freeze the image for closer study.

Chart Speed

: sets the scrolling speed of sonar chart.

Depth Curso

r: displays a cursor line on the sonar chart which allows

you to accurately measure the depth of a sonar target.

Overlay Data

: chooses what types of information (such as water tem-

perature) to display on sonar screen.

Sonar Features

: launches the Sonar Features menu which controls

options including, sonar chart mode, auto depth, surface clarity, noise
rejection, Fish I.D.



and the zoom and zone alarm bars.

Ping Speed

: sets the rate at which sonar pings are made.

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands