Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download | Manualshive

Page: 46 / 172

background image

38

Portable Sonar Installation

Like many Eagle products, the Cuda 250 sonar is capable of portable
operation. It uses the optional PPP-12 portable power pack.

The power pack and portable transducers expand the uses for your so-
nar. You can use your Cuda 250 sonar unit on your boat or take it to the
dock, on a float tube, on an ice fishing trip or use it as a second sonar in
a friend's boat. (An alternative to the PPP-12 is the PPP-15 portable
power pack, which was designed especially for ice fishing. It includes a
rechargeable gel cell battery and a transducer designed for stationary
use. The entire rig is contained in a carry bag that fits inside a five-
gallon plastic bucket.)

The PPP-12 package includes the power pack, battery adapter and a port-
able transducer. The transducer can be stored inside the power pack. The
PPP-12 requires eight AA alkaline batteries. Batteries are not included.

To use a portable power pack, you install the batteries and then attach
the sonar unit to the power pack's bracket. Plug in the
power/transducer cable and you're ready to fish.

The PPP-12 has a quick-release mounting bracket built into the case.

Installing the Batteries

Release the latch on the front of the power pack case. Open the com-
partment and install eight AA batteries into the adapter. For the long-
est life, we recommend you use alkaline batteries.

NOTE:

When the unit is not in use, we recommend you unplug the power
connector to reduce the possibility of corrosion or battery drain.
When you store the unit, always remove the batteries because dead
batteries can leak and corrode the contacts.

After installing the batteries, plug the cable's power connector into the
socket on the battery compartment cover. Route the cable's unit connec-

«
...
44
45
46
47
48
...
»

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

Brand: Navman Pages: 16

Brand: Furuno Pages: 83

FishStrike 2000

Brand: Eagle Pages: 200

Brand: Raytheon Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands