Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download

Page: 77 / 172

HyperScroll



See the entry on Ping Speed, which controls the HyperScroll feature.

Noise Rejection

See the entry on Advanced Signal Processing in this section.

Overlay Data

To change the digital data shown on top of the sonar page:

1. Press

MENU

↓

VERLAY

ATA

ENT

2. Press

↓

↑

to select

Data Type

then use

←

→

turn on the data

type and select its desired size — Small, Medium, Large or Enormous.
Data Size is displayed in the bottom of the Overlay Data Shown win-
dow and may be changed using the

←

→

keys.

Overlay Data command on the Sonar Menu (left). Overlay Data Shown

selection menu (center). In this example, we scrolled down the data list

to highlight Ground Speed. It will be displayed in a small size. Data list

with Total Distance selected (right).

After you have selected the data and the size you want, you can use

↓

↑

to select other Data Types for display.

3. To return to the previous page, press

EXIT

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands