Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download

Page: 122 / 172

114

Navigate trail: driver is headed north toward trail point (2).

Navigate a Back Trail (backtrack, or reverse)

1. Press

MENU

↓

RAILS

ENT

2. Press

↓

to enter the Saved Trail list, then use

↑

↓

to select the de-

sired

Trail Name

ENT

3. Press

↓

ELETE

RAIL

→

AVIGATE

ENT

4. Press

→

EVERSE

OUTE

ENT

←

AVIGATE

OUTE

ENT

. The unit

begins showing navigation information along the trail, in reverse.

NOTE:

If you are located at or near the end of your trail, the arrival alarm
will go off when you hit Enter. Press

EXIT

to clear the alarm.

5. Now, begin moving and let your Cuda 250 guide you.

6. When you reach your destination, be sure to cancel your navigation:
press

MENU

↓

ANCEL

AVIGATION

ENT

. The unit asks if you're

sure. Press

←

ENT

Cancel Navigation

You can turn off any of the navigation commands after you reach your
destination or at any other time by using the Cancel Navigation com-
mand. Press

MENU

↓

ANCEL

AVIGATION

ENT

←

ENT

Trail points

Present

position

arrow

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands