Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download | Manualshive

Page: 38 / 172

background image

30

Epoxy transducer to hull.

WARNING:

Use

only

the epoxy available from LEI. It has been for-

mulated to work with these installation procedures.
Other epoxy types may be too thin or may not cure to the
right consistency for optimum transducer performance.

2. The epoxy consists of the epoxy itself and a hardener. Remove the

two compounds from the package and place them on the paper plate.

Thoroughly stir the two compounds together until the mixture has a
uniform color and consistency. Do not mix too fast or bubbles will
form in the epoxy. After mixing, you have 20 minutes to complete the
installation before the epoxy becomes unworkable.

Spread a thin layer of epoxy (about 1/16" or 1.5 mm thick) on the face
of the transducer as shown in the previous figure.

Make sure there

are no air pockets in the epoxy layer!

Then, apply the remaining ep-

oxy to the sanded area on the hull.

3. Press the transducer into the epoxy, twisting and turning it to force

any air bubbles out from under the transducer face. Stop pressing

Spread epoxy here

Sand this surface

Orient the Skimmer
with the nose facing
the bow of the boat.

To bow

«
...
36
37
38
39
40
...
»

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

Brand: Topnics Pages: 5

Brand: Navman Pages: 30

Brand: Navman Pages: 88

IntelliMap 642C iGPS

Brand: Eagle Pages: 196

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands