Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download | Manualshive

Page: 27 / 172

background image

19

Align plastic ratchets in bracket.

2. Aligning the transducer on the transom.

Slide the transducer

between the two ratchets. Temporarily slide the bolt though the
transducer assembly and hold it against the transom. Looking at the
transducer from the side, check to see if it will adjust so that its face
is parallel to the ground. If it does, then the "A" position is correct for
your hull.

If the transducer's face isn't parallel with the ground, remove the
transducer and ratchets from the bracket. Place the ratchets into the
holes in the bracket with the letter "B" aligned with the dot stamped
in the bracket.

Reassemble the transducer and bracket and place them against the
transom. Again, check to see if you can move the transducer so it's
parallel with the ground. If you can, then go to step 3. If it doesn't,
repeat step 2, but use a different alignment letter until you can place
the transducer on the transom correctly.

Dot

«
...
25
26
27
28
29
...
»

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

Brand: Raytheon Pages: 90

Fishfinder 400C

Brand: Garmin Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands