Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download

Page: 95 / 172

Section 6: Basic GPS Operations

This section addresses the unit's

most

basic

GPS operations. Sec. 7,

Ad-

vanced GPS Operations

, will discuss other more advanced functions

and utilities.

Before you turn on the Cuda 250 and find where you are, it is a good
idea to learn about the different keys, the five GPS Pages and how they
all work together. BUT, if you just can't wait to get outside, turn to the
one-page

Quick Reference

on page 99.

Keyboard

Eagle Cuda 250 S/Map.

PWR

– The power key turns the unit on and off and activates the

backlight.

PAGES

– Use in conjunction with the arrow keys, the Pages key

switches the unit between the different GPS Page screens.

– Press this key to show the menus and submenus, which

allow you to select a command or adjust a feature. This also accesses
search functions for streets and intersections.

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands