Eagle Cada 250 S/Map Installation And Operation Instructions Manual Download Page 21

Page: 21 / 172

Section 2: Installation

Preparations

You can install the sonar and GPS systems in some other order if you
prefer, but we recommend this installation sequence:

CAUTION:

You should read over this entire installation section before drill-
ing any holes in your vehicle or vessel!

1. Determine the approximate location for the sonar/GPS unit, so you
can plan how and where to route the power/transducer cable. This will
help you make sure you have enough cable length for the desired con-
figuration.

2. Determine the approximate location for the transducer and its cable
route.

3. Determine the location of your battery or other power connection,
along with the power cable route.

4. Install the transducer and route the transducer cable to the so-
nar/GPS unit.

5. Route the power cable from the unit's location to an appropriate
power source and connect it there.

6. Connect the transducer/power cable to the unit and mount the so-
nar/GPS unit to the bracket.

Transducer Installation

These instructions will help you install your Skimmer



transducer on a

transom, on a trolling motor or inside a hull. Please read all instruc-
tions before proceeding with any installation.

Summary of Contents for Cada 250 S/Map












































































































































































Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for Cada 250 S/Map

Reviews:

Related manuals for Cada 250 S/Map

Brands by name

Popular brands