manualshive.com logo in svg

Eagle Cada 250 S/Map, Installation And Operation Instructions Manual

Get the comprehensive installation and operation instructions manual for the Eagle Cada 250 S/Map, absolutely free! This manual provides step-by-step guidance to set up and operate your device efficiently. Visit manualshive.com to easily download this essential manual and unlock the full potential of your Eagle Cada 250 S/Map.

Share
Download
background image

33

CAUTION:

 Failure to use the enclosed 3-amp fuse will void your warranty! For
a replacement, use a type 3AG 3-amp fuse.

This unit has reverse polarity protection. No damage will occur if the
power wires are reversed. However, the unit will not work until the
wires are attached correctly.

Mounting the Sonar Unit: In-Dash or Bracket

You can install the sonar unit on the top of a dash with the supplied
bracket. It can also be installed in the dash with an optional FM-6
dash-mounting kit.

In-dash mounting template for Cuda 250.

NOTE: This figure is

 not 

printed to scale.

Top

ALWAYS VERIFY DIMENSIONS.

Cut along this line

Summary of Contents for Cada 250 S/Map













































































































































































Reviews:

No comments

Related manuals for Cada 250 S/Map

Raymarine DS400 Owner'S Handbook Manual preview
DS400
Brand: Raymarine Pages: 96

Brands by name

Popular brands

Load more brands