Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 92

Page: 92 / 180

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

Adjusting the information displayed in the status bar

To adjust the appearance of the status bar:

1. Go to

Settings

(see above).

Fig. 60: Setting up the user interface (4)

2. Go to

Screen configuration

(4) and press on

Manual

mode - Status bar configuration

(5).



The interface used for configuring the status bar opens.

Fig. 61: Setting up the user interface (5)

3. Press and hold the desired symbol and drag it to move it into

or out of the status bar.

4. Press

to return to Settings or

to return to Manual mode.

(4) - Screen configuration

(5) - Status bar configuration

④
⑤

Summary of Contents for 878-160722-M





















































































































































































Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands