Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 55

Page: 55 / 180

Settings via the software

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

5.4.3

Sewing

Altering parameters whilst within the seam

1. Move the pedal to the

position.

2. Change the desired parameter on the control panel.
3. Press the pedal forwards and sew.



The seam will be sewn using the altered parameter value.

5.5 Automatic mode

Program numbers 001 to 999.
1. Use





to select the

Program

parameter.

2. Use





to select the program number

or another one (if

available).



The controller switches to automatic mode and the following
information appears on the display:

Fig. 32: Displey in Automatic mode

The following table shows the individual symbols on the display
and the functions of the keys on the control panel.

Summary of Contents for 878-160722-M





















































































































































































Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands