Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 28

Page: 28 / 180

Operation

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

4.3.2

Tension plate electronic

Informace

Tension plate electronic is optional equipment.

In all machines the thread from the thread reel is fed through the
thread guide and to the machine via the unwinding bracket.

Fig. 8: hread guide on the unwinding bracket and machine arm

1. Fit the thread reel on the reel stand (2).
2. Insert the thread from the rear to the front through the thread

guide on the unwinding bracket (3).

3. Use e.g. a compressed air gun to feed the thread through the

thread guide (1).

(1) - Thread guide
(2) - Reel stand

(3) - Guide on unwinding bracket

①

②

③

Summary of Contents for 878-160722-M





















































































































































































Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands