manualshive.com logo in svg

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Share
Download
Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 165

Setup

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

163

8.13 Electrical connection

8.13.1 Checking the mains voltage

Important:

 The voltage on the type plate of the sewing drive must 

correspond to the mains voltage.
1. Check the mains voltage before connecting the machine.

8.13.2 Fitting and connecting the sewing lamp and 

sewing lamp transformer

DANGER

Risk of death from electric shock!

The machine may only be connected by trained 
electricians.
Disconnect the power plug before carrying out 
work on the electrical equipment. 
Make sure the power plug cannot be accidentally 
plugged back in.
The voltage on the type plate of the sewing drive 
must correspond to the mains voltage.

DANGER

Risk of death from electric shock!

When you disconnect the sewing machine from 
the power supply at the main switch, the supply 
voltage for the sewing lamp remains active.
Pull out the power plug before fitting and 
connecting the sewing lamp and sewing lamp 
transformer. 
Make sure the power plug cannot be accidentally 
plugged back in.

Summary of Contents for 878-160722-M





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands