Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 48

Page: 48 / 180

Settings via the software

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

Information

For more information on setting control DAC Comfort can be found
in the relevant parameter sheets.

5.2 Switching the sewing machine on

Fig. 27: Display of the firmware and software version

1. Switch the main switch on.



The display shows the software version:
• On the left of the screen the control panel firmware
• On the right of the screen the controller software version



The machine performs a reference run:
The display shows the program last used, or manual mode.

Fig. 28: Display of the program last used

Fig. 29: Display in Manual mode

Down softkey

+/-

Altering sense of difference feed

Key

Function

878

2016

Summary of Contents for 878-160722-M





















































































































































































Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands