manualshive.com logo in svg

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Share
Download
Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 40

Operation

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

38

4.9 Holding the top roller in the upper position

There is a lever at the back of the machine for holding the top 
roller in the upper position.

Fig. 20: Holding the top roller in the upper position with the lever

To hold the top roller in the upper position:

1. Push the lever down.

To cancel the lock:

1. Push the lever up.

You can also use the pedal to cancel the upper position:
1. Press the pedal halfway back as when lifting the top roller.

The lever swivels back up and the lock is removed.

1

2

(1) - Top roller in upper position
(2) - Upper position canceled

Risk of crushing when lowering the top roller!

Do not hold your hands under the top roller when 
the upper position is released via the pedal or lever.

CAUTION

Summary of Contents for 878-160722-M





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands