Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 66

Page: 66 / 180

Settings via the software

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

5. Exit the submenu using

ESC





The changed values are stored immediately.

6. Exit Edit mode using

ESC

5.6.7

Copying the program

The selected program is copied into a new program number.
1. Press the

key.



The softkey menu appears.

Fig. 39: Softkey menu

2. Press the

key.



The following display appears:

Fig. 40: Copying the program



The controller displays the next free program number.

Info Screen

Display more information on the display

Speed Corr.

Setting the correction of various sewing parameters
depending on the speed of the machine.

Fabric Thickness

Setting the correction of various sewing parameters
depending on the material thickness.

Symbol

Meaning

cor.

Summary of Contents for 878-160722-M





















































































































































































Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands