Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 104

Page: 104 / 180

102

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

Options for setting the

Needle thread tension

parameter

Menu item

Setting 1

Setting 2

linear

Needle thread

tension

Value range
00 to 99 [%]

Maximum needle thread
tension reached at the
upper material thickness
limit.

Min. Material

thickness

Value range
00.0 to 10.0 [mm]

Material thickness at
which the increase in
needle thread tension
should start.

Max. Material

thickness

Value range
00.0 to 10.0 [mm]

Material thickness up to
which the increase in
needle thread tension
should occur.

2. Value On/

Off

Min. Material

thickness

Value range
00.0 to 10.0 [mm]

Material thickness from
which the 2

needle

thread tension should be
used.

2. Value On

Min. Material

thickness

Value range
00.0 to 10.0 [mm]

Material thickness from
which the 2

needle

thread tension should be
used.

Summary of Contents for 878-160722-M





















































































































































































Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Search results

Summary of Contents for 878-160722-M

Reviews:

Brands by name

Popular brands