manualshive.com logo in svg

Dürkopp Adler 878-160722-M, Operating Instructions Manual

Share
Download
Dürkopp Adler 878-160722-M Operating Instructions Manual Download Page 47

Settings via the software

Operating Instructions 878-M PREMIUM - 06.0 - 11/2021

45

5 Settings via the software

5.1 OP3000 control panel

Fig. 26: Control panel

All settings in the controller for the 878-M PREMIUM are performed 
using the OP3000 control panel.

Key

Function

0 to 9

Inputting the parameter value (if the field for the parameters 
is activated)
Selection of a parameter that is shown on the display
• Press the key under the desired symbol.

The function is selected.

ESC

Cancel the function
Exit the menu (changes remain saved)

OK

Confirm the settings
Activate the input

P

Function is different for each menu

S

Function is different for each menu

F

Function is different for each menu

Selection to the right

Selection to the left
Back one menu level

Increase the value  
Scroll through the list (upwards)

Decrease the value  
Scroll through the list (downwards)

A

Upper softkey
Assignment is different for each menu

A

B

Summary of Contents for 878-160722-M





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands