Dräger Savina 300 Technical Documentation Manual Download Page 86

Page: 86 / 166

Savina 300

Item

No.

Order No.

Description

Qty.

Qty.unit

Remark

1329472

WASHER B 5,3 DIN 9021-A4

1.000

8413621

Flat cable, Valve bench

1.000

8417820

valve unit compl.

1.000

8413603

Valve Unit

1.000

2M10633

O-RING SEAL

1.000

M11995

TOROIDAL SEALING RING

1.000

8413756

filtering plate

1.000

8413755

FILTER TUBE 1

1.000

8413754

FILTER TUBE 2

1.000

8413666

Pressure regulator

1.000

8418792

dosage insert

1.000

8416272

O-ring 2x1mm

1.000

8412993

ELECTROVALVE

1.000

M09257

PACKING RING

1.000

8417753

Ground cable -85

1.000

CH09932

RUBBER BUFFER

1.000

8418789

Grommet 9.5mm

1.000

Revision: 01

Valve unit

Parts catalog

Items that are shown in the illustration but are not listed below the illustration are not available as spare parts

14/37

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 86 / 166

Search results

Summary of Contents for Savina 300

Reviews: