Dräger Savina 300 Technical Documentation Manual Download Page 151

Page: 151 / 166

6DYLQD

5HYLVLRQ

208

000

_Pu

ati

41 / 50

Function and condition test

Function tests

Entry

Measured value (external O2 meter)

[________vol% 02]

Action

• Set specified O2 value to 21 % by volume O2.

4.2.8

Paw pressure regulation (VC-CMV/VC-AC)

Prerequisites

The Savina 300 is connected to the mains power supply and to the „O2“ com-
pressed gas supply and switched on. The Savina 300 is set to „VC-CMV/VC-
AC“ mode.

Action

• Prepare the following test setup:

Test set-up

Fig. 14

Test setup; Paw pressure regulation

Action

• Press the „Ventilation settings“ softkey and set the following parameters:

– Ti : 2.0 s

– f: 6/min

– PEEP: 5 mbar

Item

Designation

Pressure gauge

Test lung

Y-piece, adult, Luer-Lock

Adult ventilation tubing

O2 analyzer

O2 adapter

NOTE

The display message „VTi low“ on a yellow background may be triggered
during this test. It does not affect the result of measurement.

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 151 / 166

Search results

Summary of Contents for Savina 300

Reviews: