manualshive.com logo in svg

Dräger Savina 300, Technical Documentation Manual, Page: 130 / 166

Share
Download
Dräger Savina 300 Technical Documentation Manual Download Page 130

N

o

.02

08

_00

00

00

253

3_

Pu

bl

ic

ati

on

6DYLQD

Electrical safety

Electrical safety to EN 62353

20 / 50

6DYLQD

5HYLVLRQ

3.1.6

Leakage current, mains on applied part with airway temperature sen-
sor AWT 01, if installed

Prerequisites

The tester is switched on.

Action

• Prepare the following test setup:

Test set-up

Fig. 3

 

Leakage current of airway temperature sensor

Action

• (applied part) Connect the airway temperature sensor on one end to the 

device under test and on the other end by a test clip with measuring lead 
and the tester, configurable socket „A“ for applied parts (paying attention to 
the configuration!).

• Follow the instructions on the tester.

NOTE

In the following test the leakage current is measured at the airway tempera-
ture sensor AWT01. The expected value is very low (the typical measured 
value is 1.5 μA to 2 μA).

Item

Designation

1

Tester

2

Device under test

3

Connection socket of device under test

4

Airway temperature sensor AWT 01

5

Test clip with measuring lead

6

Configurable sockets for applied part

L

Conductor

N

Neutral conductor

PE

Protective earth conductor

Summary of Contents for Savina 300







































































































































































Reviews:

No comments