Dräger Savina 300 Technical Documentation Manual Download Page 123

Page: 123 / 166

6DYLQD

5HYLVLRQ

208

000

_Pu

ati

13 / 50

Maintenance parts

Maintenance parts, 8-yearly, but at the latest after 20000 operating hours

2.5

Maintenance parts, 8-yearly, but at the latest after 20000 operat-
ing hours

2.5.1

Blower

Entry

Next replacement: [________dat]

2.5.2

Service set for Savina 300

The service set (quantity 1) with the number MX08860 includes the following
items:

Entry

Next replacement: [________dat]

Quan-
tity

Designation

Number

Location/Remark

Blower with spare
parts set

8413643

Savina 300 / Trained person-
nel with product-specific Drä-
gerService training

Quan-
tity

Designation

Number

Location/Remark

Microfilter

6737545

Filter mount / Trained person-
nel

Set of dust filters S

8417898

Rear panel / Trained person-
nel

Diaphragm, com-
plete

8413661

Expiratory valve (for 2 expira-
tory valves) / Trained person-
nel

Lead-acid accumu-
lator 12 V/3.5 Ah

1841416

Compartment for the internal
battery / Trained personnel

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 123 / 166

Search results

Summary of Contents for Savina 300

Reviews: