Dräger Savina 300 Technical Documentation Manual Download Page 21

Page: 21 / 166

Savina 300

309

000

_Pu

ati

Function descriptions

Pneumatic assembly

Main components

The pneumatic assembly consists of the following components:

–

Plug-in unit

–

Valve block

–

Inspiratory block

–

Pressure measuring block

–

Patient system

–

Flow sensors

Switching valve (oxygen compensation)

Switching valve (nebulizer)

V6.1

Calibration valve (inspiratory airway pressure sensor)

V6.2

Calibration valve (expiratory airway pressure sensor)

V7.1 - V7.8

Oxygen metering valves

Pilot valve for emergency vent valve

Emergency vent valve

Inspiratory flow sensor

Expiratory flow sensor

S3.1

O2 sensor 1 (measurement and control)

S3.2

O2 sensor 2 (Monitoring)

S4.1

Inspiratory airway pressure sensor (located in inspiratory branch)

S4.2

Expiratory airway pressure sensor (located in expiratory branch)

Supply pressure sensor (oxygen)

Pressure sensor 1 (absolute pressure)

Pressure sensor 2 (absolute pressure)

Safety pressure-limitting valve (passive, approx. 120 mbar)

Emergency air valve (-3 mbar to -6 mbar)

Expiratory non-return valve

Inspiratory non-return valve

Flush flow non-return valve

Non-return valve (LPO)

Flush flow metering unit (0,1 L/min at 30 mbar)

O2 calibration metering unit for (0,1 L/min, integrated in valve block)

Metering unit for O2 measurement (0,2 L/min at 30 mbar, Sensor 3.1)

Metering unit for nebulizer (10 L/min, integrated in valve block)

R5.1 - R5.8

Metering units for the oxygen metering valves

Metering unit for O2 measurement (0,2 L/min at 30 mbar, Sensor 3.2)

Item

Designation

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 21 / 166

Search results

Summary of Contents for Savina 300

Reviews: