Dräger Savina 300 Technical Documentation Manual Download Page 38

Page: 38 / 166

.13

_00

122

ati

Savina 300

Maintenance instructions

Replacing the microfilter

Replacing the microfilter

Introduction

The following section provides a view of the microfilter and describes how to
remove and fit it.

View

The microfilter (

Fig. 28

/1) is located on the rear of the device.

Fig. 28

Device rear; microfilter

Removal

Preconditions

–

Savina 300 is switched off.

Procedure

1. Reach into the openings in the filter cover on both sides, press the

catches concealed behind them (

Fig. 29

/1) simultaneously towards

slightly, move the filter cover back slightly and take the filter cover out of
the rear panel.

2. Withdraw the power cable (

Fig. 29

/2) from filter cover guide.

Fig. 29

Savina 300 rear; filter cover

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 38 / 166

Search results

Summary of Contents for Savina 300

Reviews: