Dräger Savina 300 Technical Documentation Manual Download Page 120

Page: 120 / 166

.02

_00

253

ati

6DYLQD

Maintenance parts

Maintenance and inspection

10 / 50

6DYLQD

5HYLVLRQ

2.1

Maintenance and inspection

2.2

Maintenance parts, yearly

2.2.1

Savina 300 service set

The service set (quantity 1) with the number MX08859 includes the following
items:

Entry

Next replacement: [________dat]

NOTE

Carry out maintenance and inspection for the first time after 2 years or at the
latest after 12000 operating hours, whichever occurs first. Then yearly or af-
ter 6000 operating hours, whichever occurs first.

Quan-
tity

Designation

Number

Location/Remark

Microfilter

6737545

Filter mount / Trained person-
nel

Set of dust filters S

8417898

Rear panel / Trained person-
nel

Diaphragm, com-
plete

8413661

Expiratory valve (for 2 expira-
tory valves) / Trained person-
nel

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 120 / 166

Search results

Summary of Contents for Savina 300

Reviews: