Dräger Savina 300 Technical Documentation Manual Download Page 122

Page: 122 / 166

.02

_00

253

ati

6DYLQD

Maintenance parts

Maintenance parts, 6-yearly

12 / 50

6DYLQD

5HYLVLRQ

2.4

Maintenance parts, 6-yearly

2.4.1

Service set for Savina 300

The service set (quantity 1) with the number MX08861 includes the following
items:

Entry

Next replacement: [________dat]

NOTE

After replacing the real-time clock make the following settings on the device:

– Current date and time

– User/operator ventilation settings and alarm limits.

Quan-
tity

Designation

Number

Location / Remark

Microfilter

6737545

Filter mount / Trained person-
nel

Set of dust filters S

8417898

Rear panel / Trained person-
nel

Diaphragm, com-
plete

8413661

Expiratory valve (for 2 expira-
tory valves) / Trained person-
nel

Filter Gas inlet

8416117

O2 inlet / Trained personnel

Lead-acid accumu-
lator 12 V/3.5 Ah

1841416

Compartment (internal bat-
tery) / Trained personnel

Sealing ring

M09257

Valve block (O2) / Trained
personnel

Washer

M19311

Tubing connection / Trained
personnel

Real-time clock

1845527

Control PCB / Trained person-
nel with product-specific Drä-
gerService training

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 122 / 166

Search results

Summary of Contents for Savina 300

Reviews: