Dräger Savina 300 Technical Documentation Manual Download Page 135

Page: 135 / 166

6DYLQD

5HYLVLRQ

208

000

_Pu

ati

25 / 50

Electrical safety

Electrical safety according to IEC 60601-1

3.2.2

Protective conductor resistance

Test set-up

Fig. 5

Test setup for protective earth conductor resistance

Action

• Prepare the test setup.

• Switch on the tester and the device under test.

• Configure the tester appropriately, and follow the instructions on the tester.

• Using the tip of the test probe, scan the following points on the device

under test, move the power supply cord section-wise while doing so:

– Power supply unit earth pin

– Screws on the housing

– Oxygen connection

– Optional rails (on side of Savina)

– LPO option (connector)

Test

The protective conductor resistance must not exceed

0.2

Ohm (including

mains power cable) in each case.

Entry

Enter the highest measured value of the protective conductor resistance.

[________Ohm]

NOTE

The protective earth conductor resistance is measured with the power cable
connected.

Item Designation

Tester, e.g. SECUTEST

Device under test

Test probe with tip

Conductor

Neutral conductor

(Protective Earth) conductor

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 135 / 166

Search results

Summary of Contents for Savina 300

Reviews: