Dräger Savina 300 Technical Documentation Manual Download Page 156

Page: 156 / 166

.02

_00

253

ati

6DYLQD

Function and condition test

User-specific settings

46 / 50

6DYLQD

5HYLVLRQ

4.4

User-specific settings

4.4.1

Input of user-specific settings

Action

• Re-enter all recorded user-specific settings from the „Device configuration“

section (test item: Input of user-specific settings) in the Savina 300.

Result

The user-specific settings have been re-entered into the Savina 300.

[________OK]

4.5

Final action

Prerequisites

– The test instructions have been performed as specified.

– All tests performed were passed successfully.

4.5.1

Device handover with test label

Action

• Attach a test label to the device.

• Supply the user/owner with a fully functioning device.

Entry

[________OK]

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 156 / 166

Search results

Summary of Contents for Savina 300

Reviews: