Dräger Savina 300 Technical Documentation Manual Download Page 47

Page: 47 / 166

Savina 300

309

000

_Pu

ati

Maintenance instructions

Replacing the diaphragm of the expiratory valve

Replacing the diaphragm of the expiratory valve

Introduction

The following section provides a view of the expiratory valve diaphragm and
describes how to remove and fit it.

View

The diaphragm (

Fig. 40

/1) is located on the expiratory valve.

Fig. 40

Detail view of expiratory valve; diaphragm

Removal

1. Push the flow sensor flap (

Fig. 41

/1) up to position

2. Push the flow sensor (

Fig. 41

/2) to the left as far as it will go.

3. Turn the locking ring (

Fig. 41

/3) of the expiratory valve to the left towards

as far as it will go.

Fig. 41

Detail view of Savina 300; removing the expiratory valve

Summary of Contents for Savina 300







































































































































































Search results

Summary of Contents for Savina 300

Reviews:

Dräger Savina 300, Technical Documentation Manual, Page: 47 / 166

Search results

Summary of Contents for Savina 300

Reviews: