Dodge Journey 2011 Owner'S Manual Download Page 54 | Manualshive

Page: 54 / 559

background image

depress the button above the webbing to release the
anchorage, then move it up or down to the position that
fits you best.

As a guide, if you are shorter than average you will
prefer a lower position and if you are taller than average

you will prefer a higher position. When you release the
anchorage try to move it up and down to make sure that
it is locked in position.

In the rear seat, move toward the center of the seat to
position the belt away from your neck.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the
anchor point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,
grasp and twist the belt webbing 180 degrees to create a
fold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.

Adjusting Upper Shoulder Belt

52

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
52
53
54
55
56
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: Saab Pages: 75

Brand: AC Schnitzer Pages: 16

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Grand Cherokee WK2

Brand: Jeep Pages: 338

Challenger 2013

Brand: Dodge Pages: 543

Brand: cam Pages: 28

Brand: Mitsubishi MOTORS Pages: 416

Brand: Linear Logic Pages: 8

Brand: Buick Pages: 58

PLATINUM HT051202

Brand: Haltech Pages: 10

Brand: Suzuki Pages: 190

2013 Accord Sedan EX-L

Brand: Honda Pages: 24

2006 Escalade EXT

Brand: Cadillac Pages: 484

Brand: Axxess Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands