Dodge Journey 2011 Owner'S Manual Download Page 403 | Manualshive

Page: 403 / 559

background image

Ethanol Fuel (E-85)

E-85 is a mixture of approximately 85% fuel ethanol and
15% unleaded gasoline.

WARNING!

Ethanol vapors are extremely flammable and could
cause serious personal injury. Never have any smok-
ing materials lit in or near the vehicle when remov-
ing the fuel filler tube cap (gas cap) or filling the
tank. Do not use E-85 as a cleaning agent and never
use it near an open flame.

Fuel Requirements

Your vehicle will operate on both unleaded gasoline with
an octane rating of 87, or E-85 fuel, or any mixture of
these two. For best results, a refueling pattern that
alternates between E-85 and unleaded gasoline should be
avoided.

When you do switch fuel types it is recommended that:

•

you do not switch when the fuel gauge indicates less
than 1/4 full

•

you do not add less than 5 gallons (19 Liters) when
refueling

•

you operate the vehicle immediately after refueling for
a period of at least 5 minutes

Observing these precautions will avoid possible hard
starting and/or significant deterioration in driveability
during warm up.

NOTE:

•

When the ambient temperature is above 90° F (32° C),
you may experience hard starting and rough idle
following start up even if the above recommendations
are followed.

5

STARTING AND OPERATING

401

«
...
401
402
403
404
405
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: Kargo Master Pages: 5

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: AIS Pages: 2

Brand: Thule Pages: 12

Brand: TEINHOF Pages: 2

Brand: Gator Pages: 6

Brand: F.lli Menabo Pages: 16

OPTIA hybrid 2020

Brand: Kia Pages: 54

Brand: Edelbrock Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands