Dodge Journey 2011 Owner'S Manual Download Page 208 | Manualshive

Page: 208 / 559

background image

On steep hills, a greater speed loss or gain may occur so
it may be preferable to drive without Electronic Speed
Control.

WARNING!

Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your ve-
hicle could go too fast for the conditions, and you
could lose control and have an accident. Do not use
Electronic Speed Control in heavy traffic or on roads
that are winding, icy, snow-covered or slippery.

PARKSENSE

姞

REAR PARK ASSIST —

IF EQUIPPED

The ParkSense

威

Rear Park Assist system provides visual

and audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. Refer to “ParkSense

威

System

Usage Precautions” for limitations of this system and
recommendations.

ParkSense

威

will retain the last system state (enabled or

disabled) from the last ignition cycle when the ignition is
changed to the ON/RUN position.

ParkSense

威

can be active only when the shift lever is in

REVERSE. If ParkSense

威

is enabled at this shift lever

position, the system will remain active until the vehicle
speed is increased to approximately 11 mph (18 km/h) or
above. The system will become active again if the vehicle
speed is decreased to speeds less than approximately
10 mph (16 km/h).

ParkSense

姞

Sensors

The four ParkSense

威

sensors, located in the rear fascia/

bumper, monitor the area behind the vehicle that is
within the sensors’ field of view. The sensors can detect
obstacles from approximately 12 in (30 cm) up to 79 in

206

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
206
207
208
209
210
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: NavLinkz Pages: 4

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

Brand: Kia Pages: 54

Brand: Metra Electronics Pages: 2

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: Farad Pages: 8

Brand: Harbor Freight Tools Pages: 12

Brand: Honda Pages: 3

Brand: Whispbar Pages: 14

Brand: U.S. General Pages: 8

Brand: Quadratec Pages: 12

Brand: Meta System Pages: 22

Brand: Westfalia Pages: 10

Brand: Porsche Pages: 146

Brand: Bulldog Security Pages: 7

Brand: CITROEN Pages: 394

Brand: Quadratec Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands