Dodge Journey 2011 Owner'S Manual Download Page 435 | Manualshive

Page: 435 / 559

background image

Spare Tire Stowage

1. Place the spare tire near to the winch cable. Hold the
spare upright so that the tire’s tread is on the ground and
the valve stem is at the top of the wheel facing away from
the rear of the vehicle.

2. Tilt the retainer at the end of the winch cable and drop
it through the center of the wheel. Then place the spare
tire with the cable and retainer underneath the vehicle.

3. Fit the assembled jack-handle over the winch drive
nut. Rotate the jack-handle assembly clockwise to raise
the spare tire into the storage area. Continue to rotate the
jack-handle assembly until you hear the winch mecha-
nism click three times. It cannot be over tightened. Push
against the tire several times to be sure it is held securely
in place.

Jacking Instructions

WARNING!

Carefully follow these tire changing warnings to
help prevent personal injury or damage to your
vehicle:

•

Always park on a firm, level surface as far from
the edge of the roadway as possible before raising
the vehicle.

•

Turn on the Hazard Warning flasher.

•

Block the wheel diagonally opposite the wheel to
be raised.

•

Set the parking brake firmly and set an automatic
transmission in PARK.

•

Never start or run the engine with the vehicle on a
jack.

(Continued)

6

WHAT TO DO IN EMERGENCIES

433

«
...
433
434
435
436
437
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: Q'STRAINT Pages: 10

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 209

Brand: VBC Racing Pages: 34

2013 Corsa Infotainment system

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 236

Brand: Vauxhall Pages: 323

Brand: Mazdaspeed Pages: 8

WrapAround Windjammer

Brand: Bestop Pages: 7

Brand: Whipple Pages: 3

Brand: tams elektronik Pages: 44

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

CMPC-22 Fujitsu-Siemens PocketLoox 410

Brand: Carcomm Pages: 2

Brand: r.LiNK Pages: 21

Brand: Toyota Pages: 672

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands