Dodge Journey 2011 Owner'S Manual Download Page 226 | Manualshive

Page: 226 / 559

background image

Gate Operator/Canadian Programming

Canadian radio-frequency laws require transmitter sig-
nals to “time-out” (or quit) after several seconds of
transmission – which may not be long enough for
HomeLink

威

to pick up the signal during programming.

Similar to this Canadian law, some U.S. gate operators are
designed to “time-out” in the same manner.

It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage
door or gate motor.

If you are having difficulties programming a garage door
opener or a gate operator, replace “Programming
HomeLink

威

” Step 3 with the following:

3. Continue to press and hold the HomeLink

威

button,

while you press and release (“cycle”), your handheld
transmitter every two seconds until HomeLink

威

has

successfully accepted the frequency signal. The indica-
tor light will flash slowly and then rapidly when fully
trained.

If you unplugged the device for training, plug it back in
at this time.

Then proceed with Step 4 under “Programming
HomeLink

威

” earlier in this section.

Using HomeLink

姞

To operate, press and release the programmed
HomeLink

威

button. Activation will now occur for the

trained device (i.e., garage door opener, gate operator,
Security system, entry door lock, home/office lighting,
etc.,). The handheld transmitter of the device may also be
used at any time.

224

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
224
225
226
227
228
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: Lancia Pages: 191

Brand: Jeep Pages: 322

Brand: Jeep Pages: 341

Brand: Jeep Pages: 310

Brand: Jeep Pages: 189

Brand: Jeep Pages: 26

Brand: Jeep Pages: 21

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 209

Brand: VBC Racing Pages: 34

2013 Corsa Infotainment system

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 236

Brand: Vauxhall Pages: 177

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: Kia Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands