Dodge Journey 2011 Owner'S Manual Download Page 86 | Manualshive

Page: 86 / 559

background image

Installing The LATCH-Compatible Child Restraint
System

We urge you to follow the manufacturer’s directions
carefully when installing your child restraint. Not all
child restraint systems will be installed as described here.
Again, carefully follow the installation instructions that
are provided with the child restraint system.

NOTE:

When installing a child restraint, if it interferes

with the Head Restraint, recline the seatback slightly to
remove the interference.

The lower anchors are round bars located at the
rear of the seat cushion where it meets the
seatback and are just visible when you lean
into the rear seat to install the child restraint.

You will easily feel them if you run your finger along the
intersection of the seatback and seat cushion surfaces.

In addition, there are tether strap anchors located behind
each rear seatback, near to the floor.

Latch Anchorages

84

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
84
85
86
87
88
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

iBoard IB-ZK406

Brand: APS Auto Parts Specialist Pages: 3

Brand: Brodit Pages: 2

Brand: WABCO Pages: 48

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

2016 Sandero Stepway

Brand: Renault Pages: 183

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

Brand: Opel Pages: 254

Challenger 2013

Brand: Dodge Pages: 543

Brand: Mercedes-Benz Pages: 39

Brand: Radical Sportscars Pages: 44

Brand: Caltrend Pages: 3

Brand: Prorack Pages: 15

Brand: Scosche Pages: 32

Indash 75114-296

Brand: Panavise Pages: 2

Brand: Edelbrock Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands