Dodge Journey 2011 Owner'S Manual Download Page 440 | Manualshive

Page: 440 / 559

background image

14. Check the tire pressure as soon as possible. Adjust the
tire pressure as required.

Wheel Nuts

Tighten all wheel nuts occasionally to eliminate the
possibility of wheel studs being sheared or the bolt holes
in the wheels becoming elongated. This is especially
important during the first few hundred miles (kilome-
ters) of operation and after changing a tire. This allows
the wheel nuts to seat properly. All wheel nuts should
first be firmly seated against the wheel. The wheel nuts
should then be tightened to the recommended torque.
Tighten the wheel nuts to the final torque in increments.
Progress around the bolt circle, tightening the nut oppo-
site of the one you previously tightened until the final
torque is achieved. Recommended torque is 95 ft lbs
(130 N·m).

JUMP-STARTING

If your vehicle has a discharged battery, it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack

follow the manufacturer’s operating instructions and
precautions.

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

438

WHAT TO DO IN EMERGENCIES

«
...
438
439
440
441
442
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: Baja Designs Pages: 6

Brand: iDataLink Pages: 99

Brand: FORM FIT Pages: 2

Brand: Spiral Audio Pages: 2

autoSteady AS101

Brand: Enduro Pages: 48

Q Access Alpha GSE 2023

Brand: Q Mobility Group Pages: 9

Brand: Hyundai Pages: 19

2010 Challenger SRT

Brand: Dodge Pages: 444

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Hama Pages: 13

Brand: Mitsubishi Pages: 490

Brand: Lincoln Pages: 538

Brand: Menabo Pages: 8

Brand: Seat Pages: 372

Brand: Makita Pages: 60

2003 TraiIBIazer

Brand: Chevrolet Pages: 426

2003 S10 Pickup

Brand: Chevrolet Pages: 434

Brand: Chevrolet Pages: 516

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands