Dodge Journey 2011 Owner'S Manual Download Page 385 | Manualshive

Page: 385 / 559

background image

CAUTION!

To avoid damage to your vehicle or tires, observe the
following precautions:

•

Use chains on 215/65R16 tires only.

•

Because of restricted chain clearance between tires
and other suspension components, it is important
that only chains in good condition are used. Bro-
ken chains can cause serious damage. Stop the
vehicle immediately if noise occurs that could
indicate chain breakage. Remove the damaged
parts of the chain before further use.

•

Do not exceed 45 mph (70 km/h).

•

Drive cautiously and avoid severe turns and large
bumps, especially with a loaded vehicle.

(Continued)

CAUTION! (Continued)

•

Install chains on the front wheels as tightly as
possible and then retighten after driving about
0.5 mile (0.8 km).

•

Do not drive for prolonged periods of time on dry
pavement.

•

Observe the tire chain manufacturer’s instructions
on the method of installation, operating speed,
and conditions for use. Always use the lower
suggested operating speed of the chain manufac-
turer, if different from the speed recommended by
the vehicle manufacturer.

Always use the lower suggested operating speed if the
chain manufacturer and vehicle manufacturer suggest
different maximum speeds. This notice applies to all
chain traction devices, including link and cable (radial)
chains.

5

STARTING AND OPERATING

383

«
...
383
384
385
386
387
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: A-Tach Mounts Pages: 2

Brand: Cadillac Pages: 3

Brand: Cadillac Pages: 12

Brand: Cadillac Pages: 106

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 326

Brand: Cadillac Pages: 28

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 602

ESCALADE ESV 2004

Brand: Cadillac Pages: 20

ESCALADE EXT 2005

Brand: Cadillac Pages: 460

CT6 SUPER CRUISE 2018

Brand: Cadillac Pages: 8

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 337

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands