Dodge Journey 2011 Owner'S Manual Download Page 352 | Manualshive

Page: 352 / 559

background image

WARNING!

•

Driving through standing water limits your vehi-
cle’s traction capabilities. Do not exceed 5 mph
(8 km/h) when driving through standing water.

•

Driving through standing water limits your vehi-
cle’s braking capabilities, which increases stop-
ping distances. Therefore, after driving through
standing water, drive slowly and lightly press on
the brake pedal several times to dry the brakes.

•

Getting water inside your vehicle’s engine can
cause it to lock up and stall out, and leave you
stranded.

•

Failure to follow these warnings may result in
injuries that are serious or fatal to you, your
passengers, and others around you.

POWER STEERING

The standard power steering system will give you good
vehicle response and increased ease of maneuverability
in tight spaces. The system will provide mechanical
steering capability if power assist is lost.

If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these condi-
tions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.

NOTE:

•

Increased noise levels at the end of the steering wheel
travel are considered normal and do not indicate that
there is a problem with the power steering system.

•

Upon initial start-up in cold weather, the power steer-
ing pump may make noise for a short amount of time.
This is due to the cold, thick fluid in the steering

350

STARTING AND OPERATING

«
...
350
351
352
353
354
...
»

Summary of Contents for Journey 2011
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Journey 2011

Brand: AAMP of America Pages: 6

Brand: Triumph Pages: 86

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Skoda Pages: 165

Brand: Rugged Ridge Pages: 3

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: Veldo Teknoloji Pages: 32

Brand: RAM Pages: 148

Brand: Hamron Pages: 36

Brand: Brodit Pages: 2

Brand: PUTCO Pages: 3

Brand: Navman Pages: 27

Brand: Istar Pages: 6

Brand: Vmac Pages: 16

Brand: FAAFTECH Pages: 2

Brand: Mercedes-Benz Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands